Results 1 to 11 of 11
  1. #1
    Band Wagon
    Join Date
    Aug 2018
    Location
    MN
    Posts
    12

    Djuhnk's Minnesota Wagon Build

    Hi everyone, let me introduce you to my ride! after my 02 forester was totaled last February I started car shopping. Ive always been a Honda guy but have had Subarus for the past few years just because they are AWD. So I started looking for RT4WD wagons across the states... I came across one in Seattle I liked but it didn't have A/C. It did however only have 165000 miles and everything was stock, so I flew out and grabbed it the next week. When I actually got in the car I realized right away it needed a lot of TLC. The door locks in the back were seized shut, the fold down seat knobs were broken off, there was a mouse nest in the air ducting under the hood, and there was a pretty sizable dent in the rear driver quarter panel that was relatively fresh and cracked the paint- didn't see it in any of his pictures.

    So I got to work right away tinting the car and replacing my door lock knobs, because I had to break the other ones. (rear quarter panel dent visible in this pic)




    Mouse nest!!!


    Fast forward a couple months and I got some new enkei rims and Kumho tires for ~$600 shipped and a used set of yakima roof racks



    Very versatile vehicle with a hitch, 4wd and SUPER LOW


    I Found a used 4WD transmission locally, and grabbed it in case I need it.


    Then Winter came and after driving it through salt a few months the very small amount of rust on it and open wounds from the dent in the back panel were starting to get concerning so I decided to start taking her apart and try attempting my first paint job. Im going to do door jambs but not the engine bay. I picked a similar color and I don't have plans for this being a show car or anything so my engine bay can be a slightly different color.

    I also have started accumulating parts to go forced induction in the future. and I hope to keep updating the thread as I get more progress.
    thats all for now!!
    Last edited by Djuhnk; 03-03-2019 at 08:51 AM.

  2. #2
    Moderator
    Join Date
    Jan 2013
    Location
    Spanaway, WA YO !!!
    Posts
    737
    Good deal saving another wagon! Keep up the good work!
    88 WAGO MF !!!!

  3. #3
    Wagonist
    Join Date
    Sep 2009
    Location
    Franklin, TN
    Posts
    250
    Love that you are putting the effort and money into saving it. These wagons are going away quickly. Diggin the wood door lock!
    89 Blue RT Auto
    All stock
    DaPics!



  4. #4
    Band Wagon
    Join Date
    Jul 2016
    Location
    Sweden
    Posts
    43
    Nice, great to see a Wagon getting saved!

    P.S. Rusty exhaust tips +10hp

  5. #5
    Band Wagon
    Join Date
    Aug 2018
    Location
    MN
    Posts
    12
    update time!!!
    was doing body work over the winter, here is the car all sanded down


    Decided to paint the door jambs, so that meant taking the doors off the car for an inexperienced painter


    The biggest dent on the car, trying to pull it out.


    start of the bondo


    body painted- I used epoxy primer, urethane base and 2k clear coat.


    Heres the car mostly put back together

  6. #6
    Band Wagon
    Join Date
    Aug 2018
    Location
    MN
    Posts
    12
    After the body was done, I fired it up and drove it around the block and then started taking my engine out to do a build

    heres the stock 170k mile d16a6 pulled out of the car



    heres the block all stripped down and taken apart, I didn't find any surprises, the bearings all were in spec and my cylinder walls were still in spec, albeit slightly tapered, but I decided to run std bore and put no notch speed factory long rods and pm6 pistons back in for 10.5:1 compression



    Honed the cylinder walls with 240 grit ball hone- they were pretty badly glazed and the engine was burning a qt of oil per 1000 miles



    heres one slight problem I ran into, I didn't realize the long rods were going to send stock pm6 pistons above the deck- this is about 40 thousands above the deck, my head gasket is 48 thousands, which is too tight for things not to get kissy. So I had to clearance the cylinder head in order to make it all work.


    cylinder head clearanced so the piston would fit up inside it.


    Heres the d16a6 about to get dropped back in


    almost there!!!


    Well, things are running good, im noticing more torque for sure with the higher compression pistons, plan is to break it in and then stick a small turbo on it and get it dyno tuned. Im breaking it in with conventional oil, and revving it hard and engine braking. suggested by an article in by a sport bike engine builder.
    here is a video of it running with the built motor
    https://www.youtube.com/watch?v=vySi...ature=youtu.be

  7. #7
    Band Wagon
    Join Date
    Aug 2018
    Location
    MN
    Posts
    12
    Also decided to install A/C before the turbo goes in so that I can work around the A/c and make sure I can get things to fit

    1st step- removing this through passage


    Kinda neat they made A/c so plug and play on these, heres the plug locations that go through the firewall, the top is for the ac lines, and the bottom is for the condensate drain


    AC evaporator ready to go in


    Evaporator installed


    heres the evaporator lines as they come through the firewall


    heres the compressor bracket, compressor, belt and hoses installed as they should be. What im planning on for turbo clearances is changing the discharge line I am pointing to. It wraps all around in front of the headers, which can make things tricky for installing a turbo. im getting a half sized radiator installed and when that happens I can run that hose directly from the compressor to the condenser without the loop de loop. it'll just take a $35 custom hose and a custom compressor adapter.

  8. #8
    Wagonist
    Join Date
    Sep 2009
    Location
    Franklin, TN
    Posts
    250
    Painting the car in the garage and clearancing the head with a grinder? Good job! Adding A/C to a non-A/C wagon?? My kind of thread here. Props to you!
    89 Blue RT Auto
    All stock
    DaPics!



  9. #9
    Band Wagon
    Join Date
    Jul 2016
    Location
    Sweden
    Posts
    43
    Can only second what Arries289 said, very impressive DIY! Painting the car myself and installing AC are two things I am interested in doing too.

    Thanks for documenting your progress, it's so cool to see!

  10. #10
    council member BillBoard's Avatar
    Join Date
    Aug 2006
    Location
    Denver CO
    Posts
    3,570
    I see you are in very deep.

    Neat door locks.
    @billdirects

  11. #11
    Wagonist
    Join Date
    Jun 2013
    Location
    kincardine canada
    Posts
    171
    Great work. My next project is getting A/C to work.

Similar Threads

  1. Hi from minnesota, RT4WD wagon
    By xmodmatt in forum New User Introductions
    Replies: 10
    Last Post: 01-22-2011, 08:40 PM

Tags for this Thread

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •